Large flow submersible deep well pump 300QJ

(300QJ) submersible deep well pump manufacture ,12 submersible water pump. They are suitable for distance water irrigation , high efficiencyof increasing oxygen on agriculture, pumping water from deep well, industry, gardening, fountain etc.

♣ Pump Part: At the top of submersible motor pump,the centrifugal pump is connected with motor by rigid shaft coupling.The bearing is water lubricated.The backpressure valve is fixed on the top of the pump to avoid the working parts being damaged by the returned water in pump when the submersible motor pump stops.The water in pump can flow away through the drainage hole in the valve in case the pump is broken in winter.(Note:There is no backpressure valve in low head submersible motor pump).

♣ Motor Part: At the bottom of submersible motor pump,closed water-filled structure,guiding bearing and thrust bearing use water lubricated material.The compensation diaphragm is fixed on the bottom of motor to adjust the differential pressure caused by the ring temperature of motor.The sand-proof structure is fixed on the top of motor to prevent mud and sands to enter inside of motor.

♣ Structural features:
QJ submersible pump consists of multi-stage centrifugal impeller in series. The pump stage is connected by a flat rib or bolts, each of which is supported by a rubber (or copper) bearing, with no check valve at the top of the pump. YQS submersible motor is a closed water-filled three-phase asynchronous motor, the winding is made of water-resistant continuous sealing structure. Both the bearing and the thrust bearing are water lubricated bearings. The upper part of the motor is equipped with sand control mechanism to prevent the sediment from entering the motor internal control.

♣ Deep Well Pump Advantages

♥ Easy installation

♥ Low noise, high temperature resistence, long service life.

♥ Fully operating in water avoiding entering air.

♥ Replacing the emergency pump quickly when the pump breaks down in harsh environment such as high temperature

water tank or pool,or somewhere that are inconvenient for man to maintain.

♥ Portable design with its small size and light weight. so you neednt install bay bolt.

♣ Working conditions

1. 380V (deviation≤5%), 50Hz (deviation≤1%), 3 phases

2.Electric motor must be full of clean water

3.The first piece of impeller of pump should be at least 2m or more below dynamic water level. The distance from Pump to static water level should be not more than 70m. The distance from motor base to well bottom should be not less than 3m.

4.Water temperature should be not more than 20℃

5.Sand content of water (based on mass of sand) should be not more than 0.01%

6.PH should be 6.5-8.5

7.The content of hydrogen sulfide in water should be not more than 1.5mg/l

8.The content of chloride ions should be not more than 400mg/l

9.Water yield of water source should satisfy the demand of pump running.

♣ 300QJ Submersible Pump Model Description

300QJ 200-20

300- the overall diameter of the pump, that is, the diameter of the wells can not be less than 150mm;

QJ - well submersible pump

200 - Pump design point flow

20- pump design point head

Model Item	Head Range /m	Pump Efficiency/%	Rated Power/KW	Rated Current/A	Motor Efficiency/%
300QJ200-20/1	18-23	76	18.5	40.8	82
300QJ200-40/2	36-45	76	37	77.8	85
300QJ200-60/3	54-67	76	55	114.3	86
300QJ200-80/4	75-89	76	75	152.3	87
300QJ200-100/5	92-112	76	90	182.8	87
300QJ200-120/6	113-129	76	100	203.1	87
300QJ230-20/1	16-25	76	22	47.9	83

♣ Specifications

1.100% copper rewindable wire
2.High efficiency
3.Fast delivery time
4.Dry run pretection

♣ The Choice of Submersible Motor Pump
The followig content should be understood in order to choose and operate submersible motor pump correctly:
1 Understanding all clauses mentioned in operation conditions
2 Pay attention to the diameter and the depth of well
3 Pay attention to the static water level and the flowing water level of well
4 Pay attention to the water surging capacity of the well
The capacity,head,and the diameter of full set should be shosen according to the water surging capacity,the depth and the diameter of well.The water surging capacity of well should meet the requirement of the capacity of submersible motor pump,so that the submersible motor pump can be under the water totally when it works.

Looking for ideal Large Flow Submersible Deep Well Pump Manufacturer & supplier ? We have a wide selection at great prices to help you get creative. All the Submersible Deep Well Pump 300QJ are quality guaranteed. We are China Origin Factory of Well Pump 300QJ. If you have any question, please feel free to contact us.

Product Categories : QJ Type Submersible Well Pump